DWL-8200AP Firmware Release Notes  

Firmware: v2.10
Hardware: A2, A3
Date: 06/10/2008
 
Problems Resolved: 
1.	[SNMP] dot11SecAccountingServerPort node can not get value.
2.	[WEB] When VLAN state is enabled, change the MSSID’s security will disable MSSID’s state.
3.	[Firmware] STA couldn’t connect to multi-ssid of 11a band when eth, wlan0, wlan1 use the same mac address. So change the mac address rule back to original
4.	[Firmware] It should send an IAPP-ADD-Notify packet when STA roaming to AP2 from AP1, not only an IAPP-Move-Notify packet.
5.	[Firmware] Change the MAC address rule, eth, wlan0, wlan1 use the same mac address.
6.	[SNMP] Fix SNMP show "00:00:00:00:00:00" mac address in 11A band.
7.	 [MIB] Support WDS client info.
8.	[FW] Intel WiFi Link 4965AGN can’t connect to AP if authentication is WPA/WPA2 PSK, and vlan state is enabled.
9.	[FW] Fix the Microsoft SilverlightIE compatibility issue.
10.	[FW] Fix the WDS channel for AU domain.
11.	[FW] AP couldn’t connect to fast radius.
12.	[WEB] The Vlan tag mode should be set to Manual when Authentication is not WPA in multi-ssid page.
13.	[WEB] If enable Vlan state when the AP mode is WDS, it should pop up a warning message.
14.	[WEB] AP will crash if save Rouge AP detection info before the Radar scan complete.
15.	[WEB] User can’t configure a valid IP address(such as X.255.X.X or X.X.255.X) as a DHCP Start Address in DHCP Server page.
16.	[FW] Can’t set the ip address successful when change the boot mode from normal mode to art mode.
17.	 [FW] D-View module of DWL-8200AP can't work on D-View 5.1
18.	 [FW] A/G band IGMP snp can not play simultaneous
19.	 [WEB] The dynamic vlan mode can not set successful on the multi-ssid page of 802.11a. 
20.	 [WEB] If set the authentication to WPA-EAP, the multi-ssid page display imperfectly.
21.	[WEB] User can’t set Wireless MAC ACL.
22.	[WEB] If ap mode is not normal ap, then Grouping should be gray and can't set.
23.	[WEB] Enable VLAN State when the multi state is disabled, the radio button of band should point to “both”.
24.	[WEB] There should be a warning message, when changing primary ssid’s authentication will affect MSSID’s authentication.
25.	[CLI] When WDS or WDS with AP mode is set, disable CLI command about ratecontrol and supportrate.
26.	[FW] Only permit user manage the ap through Lan1.
27.	[FW] Mssid over WDS function has some conflict with Mssid Eth to WM filter policy, it won’t take effect if the Mssid Eth to WM filter policy is enable.
28.	[FW] Broadcast packets may miss four bytes if Vlan is enable, this will cause two station can not communicate between 802.11a&802.11g on the same vlan.
29.	[FW] Trap can’t send.
30.	[WEB] Can not change ap mode in 11g.
31.	[FW]When MSSID is enabled and authentication type is WPA-PSK in secondary SSID, the STAs which associated to secondary SSID failed to ping each other.
32.	[WEB]WDS mode shows incorrectly in 11g.
33.	[WEB] Change setting for multi-ssid, and switch to wireless page, the rompager task would crash sometimes.
34.	[WEB] The info of key type of WEP is not consistent between 11a and 11g.
35.	 Could not update fireware successfully from web.
36.	 The length of EAP passphrase has some problem.
37.	 The item of channel selection for SG domain has some problem in WDS mode.

Enhancements: 
1.	[FW] Support APMII v2.0.
2.	[FW] Modify the channel list in 11a band for U3 domain.
3.	[FW] Support DFS and TPC for AU domain.
4.	[FW] Enhance the MSSID over WDS function, allow user change the security settings of MSSID when the ap mpde is WDS with AP.
5.	[FW]Support maximum community string length to 32 characters.
6.	[FW] Modify the channel list in 11a band as the latest output power table sepc.
7.	[FW] Support WDS and WDS with AP mode in 11a for the United Kingdom (EU) domain, and restrict the channel to 36-48.
8.	.[WEB] For EU domain, remove individual country setting in 11a.
9.	[FW] Support NAP function based on dynamic vlan.
10.	[FW] Supprot ETSI DFS2.
11.	[FW] Support Primary SSID with VLAN tag function
12.	[FW] Support Administration VLAN(Manage VLAN) , administrate AP with WLAN and management IP range function
13.	[FW] Trap server settings(categorize the types of traps)
14.	[FW] Support MSSID over WDS
15.	[FW] WMM over WDS
16.	[FW] Priority by SSID
17.	[FW] IGMP Snooping (v1/v2)
18.	[FW] 802.1X Dynamic VLAN
19.	[FW] Data Rate Control follows Dlink new spec.
20.	[FW] Support IAPP (fast roaming)
21.	[FW] Enable/Disable ping
22.	Secondary RADIUS server setting
23.	[FW] AP status on UI (also on MIB)
a)	CPU and Memory utilization 
b)	Statistics for Ethernet TX and RX bytes and packets
24.	[WEB]SSID change wireless network name (SSID)
25.	[MIB]Support 802.11MIB
26.	[MIB]Support MIB-II (RFC-1213)
27.	[MIB]Support Trap002-1 spec
28.	[CLI] CLI command to input SNMP Location.
29.	[CLI] Hide the commands, get targetPower/gett controlPower/get swPower ,in CLI
30.	[CLI]Open 3 RSTP commands, rstp getstp/rstp getstate/rstp setstate
31.	Modify the WDS channel list for U3 domain, with static turbo:42,with dynamic turbo:40